|Sensing range||20 ... 60 mm , optimal distance: 45 mm|
|Transducer frequency||395 kHz|
|LED green||indication: single sheet detected|
|LED yellow||Indication: No sheet detected (Air)|
|LED red||indication: double sheet detected|
|Operating voltage U b||18 ... 30 V DC , ripple 10 % SS|
|No-load supply current I 0||< 80 mA|
|Time delay before availability t v||< 500 ms|
|Input type||Function input
0-level: -U B ... -U B + 1V
1-level: +U B - 1 V ... +U B
|Pulse length||≥ 100 ms|
|Impedance||≥ 4 kΩ|
|Output type||3 switch outputs NPN, NC|
|Rated operating current I e||3 × 100 mA , short-circuit/overload protected|
|Voltage drop U d||≤ 2 V|
|Switch-on delay T on||approx. 15 ms (shorter response time on request)|
|Switch-off delay T off||approx. 15 ms (shorter response time on request)|
|Pulse extension||min. 120 ms programmable|
|Ambient temperature||0 ... 60 °C (32 ... 140 °F)|
|Storage temperature||-40 ... 70 °C (-40 ... 158 °F)|
|Connection type||cable PVC , 2 m|
|Core cross-section||0.14 mm|
|Housing||nickel plated brass; plastic components: PBT|
|Transducer||epoxy resin/hollow glass sphere mixture; polyurethane foam|
|Supplementary information||Switch settings of the external programming adapter:
"output load": pull-up
"output logic": inv
Description of sensor functions
The ultrasonic double sheet monitor is used for double sheet detection in all situations in which the automatic distinction between double and single sheets is required in order to protect machines or avoid waste production. The double-sheet monitor is based on the ultrasonic through-beam principle. The following can be detected:
- No sheet, i.e. air,
- Individual sheet
- Double sheet
A microprocessor system evaluates the signals. The appropriate switch outputs are set as a result of the evaluation. Changes in ambient conditions such as temperature and humidity are compensated for automatically. The interface electronics is integrated into a compact M18 metal housing together with a sensor head.
The sensor is equipped with 6 connections. The functionality of the connections is described in the following table. The function input
(PK) is used to assign parameters to the sensor. (See Output pulse extension, Alignment aid and Program selection). During normal
operation, the function input must always be securely connected with +U B or -U B , to avoid possible interference or improper functionality.
|WH||Switch output for single sheets||Pulse width corresponds to the event|
|BK||Switch output for double sheets||Pulse width corresponds to the event|
|GY||Switch output for air||Pulse width corresponds to the event|
|PK||-U B /+U B||Function input for parameter assignment/
The ultrasonic sensor is working in normal mode if the function input (PK) is applied to -U B or +U B when the power source (Power-On) is supplied,
as shown in the output pulse extension table (see below).
LED yellow: Detection of air
LED green: Detection of single sheets
LED red: Detection of double sheets
The switch outputs are only active in normal operation!
White: WH Single sheet output
Black: BK Double sheet output
Gray: GY Air output
Procedure for assigning parameters
It is possible to switch to additional parameter assignment modes from the display mode:
Alignment mode -->
Program selection mode -->
Alignment aid mode --> (for checking)
When the function input (PK) is applied to -U B (for > 500 ms), the mode changes. When the "Program selection“ mode is active, swit-
ching on function input (PK) on to +U B (for > 500 ms) selects the next program level.
Disconnecting the power supply causes the system to exit the current mode with the selected program change.
The switch outputs are not active while parameters are being assigned to the sensor!
During installation, the amplitude control can be used to check whether the ultrasonic amplitude at the receiver is sufficient. If the transmitter is not aligned properly in relation to the receiver, maximum sound energy is not transmitted to the receiver, which may result in the incorrect detection of materials.
When the ultrasonic sensor detects an area of air (yellow LED lights up), the UDC begins to display the strength of the measured amplitude signal:
- if the signal is weak, the yellow LED flashes at low frequency
- the flashing frequency increases in line with the signal strength
- the yellow LED lights up continuously when the signal strength is sufficient.
The single sheet function (green LED) and double sheet function (red LED) are now active. This can be used to check the correct
function of the sensor.
In the program selection mode, the current program is displayed by the green LED (number of flashing pulses = program number).
Applying the adjustment input (PK) to +U B (for > 500 ms) causes the next program to be selected in cyclic sequence (program 1 follows through to program 4).
(1)If ship by sea and Air,you can get Bill of Loading,CO,Commerical invoice,Packing list from us after ship.
(2)If ship by express company,you will get a Tracking No. from us after ship.
Yueqing Winston Electric Co., Ltd. is not only an exporting company, but also a professional manufacturer in China. We have our own production base. The products we professionally deal with are switching power supplies, sensors, frequency inverter, heater, thermostat, AC contactors, circuit breakers and others.
|Contact Person :||Cui|